
ARCHITECTURAL SPECIFICATIONS & ROUGH-IN INFORMATION
STANDARD LENGTH MODELS
Exterior Dimensions
Width | All models below (Door Closed) | 36" |
Width | All models below (Door Opened) | 34.25" |
Length | MB-59-AV —Alcove Placement | 59.5" |
Length | MB-68-AVH —Head End Corner Placement | 62.5" |
Length | MB-68-AVF —Foot End Corner Placement | 62.5" |
Length | MB-68-AV —Standard Wall Placement | 65.5" |
Height | All models above to the top of controls | 46.5" |
Interior Dimensions
Length-Straight | 45" |
Length-Diagonal | 47" |
Seat Depth | 22" at Widest Point |
Seat Area Width (w/ Door Closed) | 25" |
Seat Height | 21.5" |
Specifications
Back Flow Prevention: | Double check valves for shower wand complies with CSA B64.7, UPC, Certified to NSF/ANSI 372, ASSE 1035—“Laboratory Faucet Vacuum Breakers”. Fill: 1.5” A gap above rim complies with National Plumbing Standards. (See plumbing standards below.) Note: The factory provided backflow prevention is the most widely accepted. Local codes may require changes. The local plumbing contractor is responsible for any changes. |
BathAire(SM) Outlets: | 4 with 12 ports each for a total of 48 warm air massage outlets. |
Door Seal: | Seal certified by Warnock Hersey to the ASME A112.19.15-2005, CSA B45.0-02 (R2008) and ANSI Z124.1.2 (2008) standards to ensure long lasting durability for bathtubs with pressure sealed doors. Highly resistant to oils, detergents and all water conditions. |
Electrical: | Factory provided on board installed dead front GFCI: UL/CSA approved. |
Installation Time: | 1 hour (when water and electrical supplies meet the provided rough-ins.) Inspection and Adjustments: 1/2 hour |
Motor Specs: | Door motor: 115 V., 4.2 Amp, 1/3 H.P. BathAire(SM) Motor: 120 V, 11 Amp, 1.3 H.P. Variable speed with built-in 600 watt heating element for maximum comfort and control. |
Room Size: | 5' 11" wide x 9' 7 ½” long minimum recommended. Can fit in smaller room--call MasterCare with dimensions. |
Electrical Standards: | CAN/CSA C22.2 No. 218.2-93 (R2006) Hydromassage Bathtub Appliances. UL 1795 Hydromassage Bathtubs, Issue: 2009/08/05 Ed: 4 Rev: 2010/03/23 |
Plumbing Standards: | Warnock Hersey: CSA B45.5 (2008), ASME A112.19.15 (2005), CSA B45S1 (2004), ANSI Z124.1.2 (2005). |
Switches: | Membrane and Pneumatic. |
Thermometer: Tub | Solar / Digital temperature measurements. |
Door/Entry: | Door full length of tub with tub seat extending over the floor surface. |
Tub Fill/Shower: | Built-in thermostatic mixing valve certified to ASSE 1016-2005, ASME A112.18.1-2005, CSA B125 and UPC listed. |
Tub Fill / Shower shut off: | Valves certified ASSE and UPC listed with ceramic disc controls. |
Tub Shell: | Sanitary gel-coated FRP (Fiberglass Reinforced Polymer). |
Tub Water Use: | 45 gallons minimum with normal displacement 4 inches below overflow escutcheon. |
Waste: | 2" PVC schedule 40 pipe. DO NOT Hard-Plumb for ease of accessibility for servicing. |
Water Connection: | ¾” SS braided flex hose with female pipe thread connections. |
Water Supply: | ¾” hot and cold with shut-offs. Hot and cold water pressure 45-90 psi. Hot water temperature to be 120º F and cold water 59º F. |
Weight: | 500 lbs. |
Fill Rate: | In excess of 17 GPM provided that the water lines are ¾”, water pressure is at least 60 psi and the hot water is 120º F. Community and/or other environmental factors may affect the fill rate. |
Establishment Registration: | 3003336913 |
EXTENDED LENGTH MODELS
Exterior Dimensions
Width | All models below (Door Closed) | 36" |
Width | All models below (Door Opened) | 34.25" |
Length | MB-59-AV —Alcove Placement | 65.5" |
Length | MB-68-AVH —Head End Corner Placement | 68.5" |
Length | MB-68-AVF —Foot End Corner Placement | 68.5" |
Length | MB-68-AV —Standard Wall Placement | 71.5" |
Height | All models above to the top of controls | 46.5" |
Interior Dimensions
Length-Straight | 51" |
Length-Diagonal | 52" |
Seat Depth | 22" at Widest Point |
Seat Area Width (w/ Door Closed) | 25" |
Seat Height | 21.5" |
Specifications
Back Flow Prevention: | Double check valves for shower wand complies with CSA B64.7, UPC, Certified to NSF/ANSI 372, ASSE 1035—“Laboratory Faucet Vacuum Breakers”. Fill: 1.5” a gap above rim complies with National Plumbing Standards. (See plumbing standards below.) Note: The factory provided backflow prevention is the most widely accepted. Local codes may require changes. The local plumbing contractor is responsible for any changes. |
BathAire(SM) Outlets: | 4 with 12 ports each for a total of 48 warm air massage outlets. |
Door Seal: | Seal certified by Warnock Hersey to the ASME A112.19.15-2005, CSA B45.0-02 (R2008) and ANSI Z124.1.2 (2008) standards to ensure long lasting durability for bathtubs with pressure sealed doors. Highly resistant to oils, detergents and all water conditions. |
Electrical: | Factory provided on board installed dead front GFCI: UL/CSA approved. |
Installation Time: | 1 hour (when water and electrical supplies meet the provided rough-ins). Inspection and Adjustments: 1/2 hour |
Motor Specs: | Door motor: 115 V, 4.2 Amp, 1/3 H.P. BathAire(SM) Motor: 120 V., 11 Amp, 1.3 H.P. Variable speed with built-in 600 watt heating element for maximum comfort and control. |
Room Size: | 6’ 5" wide x 10’ 1½” long minimum recommended. Can fit in smaller room--call MasterCare with dimensions. |
Electrical Standards: | CAN/CSA C22.2 No. 218.2-93 (R2006) Hydromassage Bathtub Appliances. UL 1795 Hydromassage Bathtubs, Issue: 2009/08/05 Ed: 4 Rev: 2010/03/23 |
Plumbing Standards: | Warnock Hersey: CSA B45.5 (2008), ASME A112.19.15 (2005), CSA B45S1 (2004), ANSI Z124.1.2 (2005). |
Switches: | Membrane and Pneumatic. |
Thermometer: Tub | Solar / Digital temperature measurements. |
Door/Entry: | Door full length of tub with tub seat extending over the floor surface. |
Tub Fill/Shower: | Built-in thermostatic mixing valve certified to ASSE 1016-2005, ASME A112.18.1-2005, CSA B125 and UPC listed. |
Tub Fill / Shower shut off: | Valves certified ASSE and UPC listed with ceramic disc controls. |
Tub Shell: | Sanitary gel-coated FRP (Fiberglass Reinforced Polymer). |
Tub Water Use: | 55 gallons minimum with normal displacement 4 inches below overflow escutcheon. |
Waste: | 2" PVC schedule 40 pipe. DO NOT Hard-Plumb for ease of accessibility for servicing. |
Water Connection: | ¾” SS braided flex hose with female pipe thread connections. |
Water Supply: | ¾” hot and cold with shut-offs. Hot and cold water pressure 45-90 psi. Hot water temperature to be 120º F and cold water 59º F. |
Weight: | 500 lbs. |
Fill Rate: | In excess of 17 GPM provided that the water lines are ¾”, water pressure is at least 60 psi and the hot water is 120º F. Community and/or other environmental factors may affect the fill rate. |
Establishment Registration: | 3003336913 |